ProSoundWeb Community

Please login or register.

Login with username, password and session length
Advanced search  
Pages: 1 2 [3] 4   Go Down

Author Topic: B&C Subs - merged  (Read 10736 times)

Marjan Milosevic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 681
Re: Planning on building 2- B&C SUB215 subs
« Reply #20 on: March 16, 2009, 06:57:06 am »
You didnt make any space for mounting a grill.
You should have placed the baffle some 5cm towards the back of the box.
Logged

Elliot Thompson

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1573
Re: Planning on building 2- B&C SUB215 subs
« Reply #21 on: March 16, 2009, 07:22:36 am »
Marjan Milosevic(MarjanM) wrote on Mon, 16 March 2009 10:57

You didnt make any space for mounting a grill.
You should have placed the baffle some 5cm towards the back of the box.



It seems cost is the motive, after reading the thread. So he might go with...

http://akamaipix.crutchfield.com/products/2003/125/h125g12-fp.jpg


Worst case scenario he can attach shims as a frame for a full size grille to sit in.


Best Regards,
Logged
Elliot

Shivraj Persaud

  • Newbie
  • *
  • Offline Offline
  • Posts: 39
Re: Planning on building 2- B&C SUB215 subs
« Reply #22 on: March 16, 2009, 04:49:48 pm »
yes I bought a pair of grills from parts express, my friend is cutting it for me right now. The grill wasnt long enough so I had to take some from the width and add to the height.
Logged

Shivraj Persaud

  • Newbie
  • *
  • Offline Offline
  • Posts: 39
Re: Planning on building 2- B&C SUB215 subs
« Reply #23 on: April 02, 2009, 07:08:03 pm »
finally fired it up, only one of these sounds amazing. Running it through a yamaha p2500s bridged, gotta turn gain all the way up, pretty hard to get it to clip though ... but its really loud. any thoughts on amp?
Logged

George Friedman-Jimenez

  • Sr. Member
  • ****
  • Offline Offline
  • Posts: 302
Re: Planning on building 2- B&C SUB215 subs
« Reply #24 on: April 04, 2009, 03:56:35 pm »
Nice job. How much does it weigh with drivers?
Logged

Shivraj Persaud

  • Newbie
  • *
  • Offline Offline
  • Posts: 39
Re: Planning on building 2- B&C SUB215 subs
« Reply #25 on: April 10, 2009, 11:56:26 pm »
it weighs about 140-150 lbs, not light, but good dimensions, not that high but deep.

Logged

Douglas R. Allen

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 776
    • http://-
Re: Planning on building 2- B&C SUB215 subs
« Reply #26 on: April 13, 2009, 07:23:12 pm »
When you have them all done could you post a picture?
Also a link to the plans?
Douglas R. Allen
Logged
Allen Audio

"The worst thing is."
"You can't teach common sense."

George Friedman-Jimenez

  • Sr. Member
  • ****
  • Offline Offline
  • Posts: 302
Re: Planning on building 2- B&C SUB215 subs
« Reply #27 on: April 13, 2009, 09:34:45 pm »
Logged

Shivraj Persaud

  • Newbie
  • *
  • Offline Offline
  • Posts: 39
Re: Planning on building 2- B&C SUB215 subs
« Reply #28 on: April 25, 2009, 12:41:37 am »
question about power amp, thinking about building more of these subs and powering them with a crest ca18 or ca12 .. cause I want to run them in parallel to get more out of them. Looking at the impedance response curve I can get down to 2 ohms. But how would you provide power to the amp, I see these amps require up to 60 amp service, can you build or buy something that can store the power? like a capacitor?
Logged

Duncan McLennan

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2375
Re: Planning on building 2- B&C SUB215 subs
« Reply #29 on: April 25, 2009, 09:29:50 am »
No... you just use a power source that has a large enough supply.

The amplifiers will not draw 60A.  Check the spec sheer for ratings for 1/3 and 1/8 power.  If you've got enough subs/amps the most you should be drawing is about 1/8 (that's the average power the amplifier draws when you're just barely touching the clip lights).

I would think you'd be more than fine running each one on a 15 or 20A circuit.
Logged
dcm
Waterloo & London, Ontario
Pages: 1 2 [3] 4   Go Up
« previous next »
 

Page created in 0.051 seconds with 19 queries.