ProSoundWeb Community

Please login or register.

Login with username, password and session length
Advanced search  

Pages: [1]   Go Down

Author Topic: Slanted Rack for LS9-16  (Read 3529 times)

Derek Van Winkle

  • Newbie
  • *
  • Offline Offline
  • Posts: 14
Slanted Rack for LS9-16
« on: February 17, 2011, 11:02:49 AM »

What slanted rack is available for the LS9-16?

I'm looking for something with about 10-12U underneath for racking up wireless mics and other equipment.

Thanks,
Logged

Luke Robinson

  • Full Member
  • ***
  • Offline Offline
  • Posts: 130
    • audio gods
Re: Slanted Rack for LS9-16
« Reply #1 on: February 18, 2011, 07:45:04 AM »

I used the oddessy, it works great but I had to do some modifications. You will need to lower the top set of rack rails so that the lid will close over the tilted screen of the ls9. This also involves chopping about an inch off the top of the front ralis to accommodate.
It took me less than an hour to do the whole lot of it.
Logged

Bob Leonard

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 6807
  • Boston, MA USA
Re: Slanted Rack for LS9-16
« Reply #2 on: February 19, 2011, 12:21:42 AM »

Road Ready offers some high quality racks just for this purpose. Years ago I turned to Riad Ready and have been happy ever since. Not the cheapest, not the most expensive, but amoung the best.
Logged
BOSTON STRONG........
Proud Vietnam Veteran

I did a gig for Otis Elevator once. Like every job, it had it's ups and downs.

michael glenn

  • Newbie
  • *
  • Offline Offline
  • Posts: 11
Re: Slanted Rack for LS9-16
« Reply #3 on: February 19, 2011, 03:50:25 PM »

I bought a C4UE-P-22 from EWI cases

Perfect for me, medium duty, good quality plus I'm a fan of EWI Cases.  The right size too,  my LS9-16 doesn't hang over the front rack rails.  4 rack spaces below or you can get a variant with 6 rack spaces.

http://www.audiopile.net/products/Cases/CU_series_roadracks/CU-P-22/CU-P-22_series_cutsheet.shtml



Logged

Doug Fowler

  • Member since May 1995, 2nd poster on original LAB, moderator on and off since 1997, now running TurboMOD v1.826
  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2331
  • Saint Louis, MO USA
Re: Slanted Rack for LS9-16
« Reply #4 on: February 19, 2011, 04:29:51 PM »

I bought a C4UE-P-22 from EWI cases

Perfect for me, medium duty, good quality plus I'm a fan of EWI Cases.  The right size too,  my LS9-16 doesn't hang over the front rack rails.  4 rack spaces below or you can get a variant with 6 rack spaces.

http://www.audiopile.net/products/Cases/CU_series_roadracks/CU-P-22/CU-P-22_series_cutsheet.shtml

But can you apply the lid with XLRs patched into the LS-9?

I bought a couple of these a couple of years ago, and that is my only issue for LS-9 use.

BTW I think right angle XLRs solves it.

Logged
Brawndo, the Thirst Mutilator. 
It's got electrolytes. 
It's got what plants crave.

michael glenn

  • Newbie
  • *
  • Offline Offline
  • Posts: 11
Re: Slanted Rack for LS9-16
« Reply #5 on: February 19, 2011, 05:06:07 PM »

The rack slant mixer case I bought (C4UE-P-22) from EWI is a relatively new item (6months??), it's a full 22" deep so the LS9-16 fits nicely on the top rack rails.  Deep enough that the XLR's on the back stay connected with just enough room for the lid. I have two Behringer ADA8000 in the rack spaces below, those XLR's stay connected as well.

 The 22" depth makes all the difference.  All my XLR's are straight, no issues on the front or back with this 22" depth.

EWI sells the same configuration with 18" depth, that model is more suited to a MixWizard size.

   
But can you apply the lid with XLRs patched into the LS-9?

I bought a couple of these a couple of years ago, and that is my only issue for LS-9 use.

BTW I think right angle XLRs solves it.

edited for typos ;-)
« Last Edit: February 19, 2011, 05:14:34 PM by michael glenn »
Logged

Joe Brugnoni

  • Newbie
  • *
  • Offline Offline
  • Posts: 32
Re: Slanted Rack for LS9-16
« Reply #6 on: February 19, 2011, 07:02:23 PM »

I have two of the EWI and I have a 01v96 in it with everything patched and it works fine
Logged

John Livings

  • Sr. Member
  • ****
  • Offline Offline
  • Posts: 351
  • Los Angeles, California
Re: Slanted Rack for LS9-16
« Reply #7 on: February 21, 2011, 01:12:17 AM »

You might look at the OSP, 25 inch Deep Case.

http://www.youtube.com/watch?v=ROUN0S2cRPk

Regards,  John
Logged

ProSoundWeb Community

Re: Slanted Rack for LS9-16
« Reply #7 on: February 21, 2011, 01:12:17 AM »


Pages: [1]   Go Up
 



Site Hosted By Ashdown Technologies, Inc.

Page created in 0.05 seconds with 23 queries.