ProSoundWeb Community

Please login or register.

Login with username, password and session length
Advanced search  

Pages: [1] 2  All   Go Down

Author Topic: Church speakers proposal  (Read 6437 times)

Russ Buck

  • Newbie
  • *
  • Offline Offline
  • Posts: 11
Church speakers proposal
« on: January 31, 2011, 08:19:18 pm »

Attached is a speaker recommendation for our sanctuary.  Can I get some feedback as to what is shown here.  For those who haven't read my earlier post.  sanctuary seats approx. 150 is 45' wide x 50 deep. 25' high ceiling.  the center cluster pictured is 11' from the back wall and 16 1/2' off the floor to top of speaker. the front row of seats start at 15' from the back wall.    The speaker would hang right under the light toward the back wall.  (just behind light)
« Last Edit: February 01, 2011, 10:11:22 am by Russ Buck »
Logged

Russ Buck

  • Newbie
  • *
  • Offline Offline
  • Posts: 11
Speaker proposal SPL Maping
« Reply #1 on: January 31, 2011, 08:30:10 pm »

 >:(here is the SPL charts
« Last Edit: February 01, 2011, 10:57:19 am by Russ Buck »
Logged

Russ Buck

  • Newbie
  • *
  • Offline Offline
  • Posts: 11
Re: Church speakers proposal
« Reply #2 on: February 01, 2011, 12:03:08 pm »

Also I am trying to figure out the best way hook these up. 1. do I buy a cross over like DBX223xl, or do I buy a amp like crownxti2000 and use one channel for mains and one channel for sub and use its' onboard cross over?  any suggestions pros and cons?
Logged

John Fiorello

  • Jr. Member
  • **
  • Offline Offline
  • Posts: 60
Re: Church speakers proposal
« Reply #3 on: February 01, 2011, 01:18:43 pm »

Hi Russ!

I don't know if I'm reading this right, but your mains look like they go from 80 or 90 degrees at 1k to 30 degrees at 2k (vertical dispersion).  Your models don't show poor coverage in the first few rows, but that was my initial concern.  Are your older posts on the old board?  I'll go check them out for more detail if it's been addressed.


JF

Logged
Stop.  Think.  Speak.

Michael Galica

  • Church and H.O.W. Forums
  • Newbie
  • *
  • Offline Offline
  • Posts: 18
Re: Church speakers proposal
« Reply #4 on: February 01, 2011, 02:21:41 pm »

Also I am trying to figure out the best way hook these up. 1. do I buy a cross over like DBX223xl, or do I buy a amp like crownxti2000 and use one channel for mains and one channel for sub and use its' onboard cross over?  any suggestions pros and cons?

The proposal didn't include amps or anything just speakers?  That's a little odd in my experience.  If it were me, I'd want to have at least three amp channels, one for the subs, one for the LF driver of the mains, and one for the HF driver.  But the best thing to do would be to talk to whoever gave the recommendation and see what they suggest to achieve the coverage they've modeled for you.

Also, don't be surprised if you get a large number of people chiming in with things like "don't install them yourself unless you happen to be a qualified rigger and the plan was stamped by a licensed structural engineer". 
Logged
Mike Galica
Pastor
Holy Cross Lutheran Church

Brad Weber

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2209
  • Marietta, GA
Re: Church speakers proposal
« Reply #5 on: February 01, 2011, 02:50:37 pm »

I'm not sure if you were looking for comments on the proposal in general, the prediction information or both.  So I'll assume both.

In general, that seems like a reasonable system approach.  I agree with John that the large difference in the vertical pattern of the CPL42-94 between 1kHz and 2kHz does not seem to be reflected in the results, however that may be due to seeing only the direct coverage of the listeners and not how that variation may be affecting the sound hitting the walls, ceilings or stage.

Are the EASE model and predictions something a consultant, contractor or dealer created for you or something you created?  Some purely generic comments are to make sure that interference is turned on for the predictions, in EASE one button click determines whether or not the predictions include interference between multiple speakers or not and in some cases that can make a significant difference in the results.  Also, while predicting the direct levels is important and having good coverage for the direct levels is critical to achieving a good overall result, it is good to also look at ALCONS, STI and D/R ratio predictions that assess the impact of the indirect sound and the resulting intelligibility.  Think of it this way, does it matter if everyone hears the same thing if no one understands what it is?  And last, it seems that the audience areas are predicted but not the 'stage' area.  I personally always include the stage or platform areas in modeling in order to see what is happening where the microphones will be located, you don't want to find out later that the highest levels in the room turn out to be right where the pastor normally stands.  I would be a bit concerned about that here as it looks like at 250Hz there is a 'hot spot' that may extend onto the middle of the platform area.

To be fair, predicting the indirect sound components and intelligibility takes more time not just in the actual prediction computations but also with sufficiently modeling the entire room and related finishes.  It is typically not something a Contractor can 'throw in' as part of an equipment sale and is instead a design effort that may require compensation.  But it is also where the much of the value in predictive modeling correlating to the actual results can be gained.
Logged

Russ Buck

  • Newbie
  • *
  • Offline Offline
  • Posts: 11
Re: Church speakers proposal
« Reply #6 on: February 01, 2011, 03:40:45 pm »

Brad these were done by the Technical Applications Engineer for Community loudspeaker co. 
Logged

Brian Ehlers

  • Full Member
  • ***
  • Offline Offline
  • Posts: 126
  • West Michigan
Re: Church speakers proposal
« Reply #7 on: February 01, 2011, 06:22:30 pm »

.... I would be a bit concerned about that here as it looks like at 250Hz there is a 'hot spot' that may extend onto the middle of the platform area.
I'll echo this concern.  This is a common problem when you have a central cluster arranged horizontally with the pulpit pretty much directly below it.  Almost all loudspeakers have very little directionality at 250 Hz and below, so all three in the cluster get summed full-force on the floor below them.

I'm not saying there's anything wrong with the cluster as proposed, but you can expect to have to take some measures to clear up the mud in the 200 - 300 Hz range.  You can cut some of this out on the affected mic channel EQs.  Another good approach is to use a little delay between the speakers in the cluster to steer the lobe away from the stage.

The success of your system will be highly dependent on having a qualified engineer tune it.  You really don't want to skip this step;  it's more important (in my opinion) than some of the up-front work you're doing right now.  Of course, if you're going to ask someone to tune the system, you should also involve him in the up-front work -- both for his sake and yours.
Logged

DonSneed

  • Newbie
  • *
  • Offline Offline
  • Posts: 11
Re: Church speakers proposal
« Reply #8 on: February 16, 2011, 07:50:04 pm »

Russ have you looked at the OAP Audio C-1.5....I use these a lot in churches, it has a 15" wloofer, a 1" coaxle 60x30 long throw horn & a second horn under the cabinet for near field short throw horn 90x40, the cabinet has two L-pads to level out the highs. The long throw is aim for the middle to rear seating & the short throw horn is aimed for the front row to middle seating area. Add two low profile subs.....the sound coverage is great....
Logged

Brad Weber

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2209
  • Marietta, GA
Re: Church speakers proposal
« Reply #9 on: February 17, 2011, 08:26:14 am »

Russ have you looked at the OAP Audio C-1.5....I use these a lot in churches, it has a 15" wloofer, a 1" coaxle 60x30 long throw horn & a second horn under the cabinet for near field short throw horn 90x40, the cabinet has two L-pads to level out the highs. The long throw is aim for the middle to rear seating & the short throw horn is aimed for the front row to middle seating area. Add two low profile subs.....the sound coverage is great....
I used OAP C series speakers some 20-25 years ago.  If you notice, there is no overall directionality data provided for the C Series and the EASE data requires you to treat the main coax and the 'short throw' horn as two separate devices.  This reflects the challenge with the concept as how the two horns interact and the resulting pattern and response are dependent on the aiming of the bottom 'short throw' horn.  You could have significant overlap and combfiltering or you might have a significant gap.  So an interesting concept but one for which the performance and result is unfortunately difficult to predict without modeling.
Logged
Pages: [1] 2  All   Go Up
 


Page created in 0.038 seconds with 23 queries.