ProSoundWeb Community

Please login or register.

Login with username, password and session length
Advanced search  

Pages: [1]   Go Down

Author Topic: Article Photo  (Read 3789 times)

Charlie Zureki

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1244
  • South Eastern Michigan (near Windsor)
Article Photo
« on: July 14, 2011, 12:45:29 PM »
  Scanning the site's homepage ads I noticed the rigging article by Ken Deloria.  While reading the article, I expected a note, or disclaimer regarding the photo that was inserted at the top of this article, but didn't find it. 

  The photo should have had a disclaimer stating "how not to rig truss".   

  I'm certain that Ken did not submit this photo on a proper rigging primer.

   Cheers,
   Hammer
Logged
Do it the right way....don't be a Dino!

Rex Ray

  • Newbie
  • *
  • Offline Offline
  • Posts: 20
    • Clair Global
Re: Article Photo
« Reply #1 on: July 14, 2011, 01:52:38 PM »
Quote from: Charlie Zureki on July 14, 2011, 12:45:29 PM
  Scanning the site's homepage ads I noticed the rigging article by Ken Deloria.  While reading the article, I expected a note, or disclaimer regarding the photo that was inserted at the top of this article, but didn't find it. 

  The photo should have had a disclaimer stating "how not to rig truss".   

  I'm certain that Ken did not submit this photo on a proper rigging primer.

   Cheers,
   Hammer

Hammer,I was going to comment on that very thing this morning,but work interfered!
Rex Ray
Sr. Engineer
Clair Nashville
Logged

Andrew (A.J.) McGlynn

  • Newbie
  • *
  • Offline Offline
  • Posts: 7
  • Houston TX
Re: Article Photo
« Reply #2 on: July 14, 2011, 02:35:15 PM »
I am no rigger by any means but even I know that its wrong.
Logged

Tim McCulloch

  • SR Forums
  • Hero Member
  • *
  • Online Online
  • Posts: 23774
  • Wichita, Kansas USA
Re: Article Photo
« Reply #3 on: July 14, 2011, 02:45:03 PM »
Quote from: Charlie Zureki on July 14, 2011, 12:45:29 PM
  Scanning the site's homepage ads I noticed the rigging article by Ken Deloria.  While reading the article, I expected a note, or disclaimer regarding the photo that was inserted at the top of this article, but didn't find it. 

  The photo should have had a disclaimer stating "how not to rig truss".   

  I'm certain that Ken did not submit this photo on a proper rigging primer.

   Cheers,
   Hammer

Famous words of rigging:  compression, not tension.
Logged
"If you're passing on your way, from Palm Springs to L.A., Give a wave to good ol' Dave, Say hello to progress and goodbye to the Moonlight Motor Inn." - Steve Spurgin, Moonlight Motor Inn

paul bell

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 609
Re: Article Photo
« Reply #4 on: July 14, 2011, 03:29:41 PM »
Where might we find this article? Can you post a link?
Logged

Charlie Zureki

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1244
  • South Eastern Michigan (near Windsor)
Re: Article Photo
« Reply #5 on: July 14, 2011, 04:07:05 PM »
Quote from: paul bell on July 14, 2011, 03:29:41 PM
Where might we find this article? Can you post a link?

   Hello Paul,

   You passed it, it's this site's home page.

  Cheers,
  Hammer
Logged
Do it the right way....don't be a Dino!

Mac Kerr

  • Old enough to know better
  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 7562
  • Audio Plumber
Re: Article Photo
« Reply #6 on: July 14, 2011, 07:22:05 PM »
Quote from: Charlie Zureki on July 14, 2011, 04:07:05 PM
   Hello Paul,

   You passed it, it's this site's home page.

  Cheers,
  Hammer

It's on ProSoundWeb's home page, not the forum home page. Here is a LINK.

Mac
Logged

ProSoundWeb Community

Re: Article Photo
« Reply #6 on: July 14, 2011, 07:22:05 PM »

Pages: [1]   Go Up
« previous next »
 



Site Hosted By Ashdown Technologies, Inc.

Page created in 0.047 seconds with 25 queries.