ProSoundWeb Community

Please login or register.

Login with username, password and session length
Advanced search  

Pages: 1 2 [3]   Go Down

Author Topic: Eclipse Audio FIR Designer  (Read 2904 times)

Kent Clasen

  • Full Member
  • ***
  • Offline Offline
  • Posts: 157
Re: Eclipse Audio FIR Designer
« Reply #20 on: December 13, 2021, 06:24:38 PM »

I use RePhase, which is free. No automatic stuff, and the interface isn't amazing, but it's worked well for me.

Chris

Hi Chris-

I just downloaded RePhase. Do you use SMAART? I can't figure out how to import a measurement file into RePhase. I saved the SMAART measurement as an ASCII file but RP says it is not the correct format.

I tried the trial of FIR Creator and it opens the SMAART file just fine.
Logged

Chris Grimshaw

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1740
  • Sheffield, UK
    • Grimshaw Audio
Re: Eclipse Audio FIR Designer
« Reply #21 on: December 17, 2021, 01:42:01 PM »

Hi Kent,

Thanks for giving it a try. I use REW.

My workflow is:
- Take measurement in REW
- Adjust vertical scale so it's nominal 0dB, because that fits RePhase nicely.
- Export the single measurement as a CSV file (comma spaced variable, it's in the export settings), with the file extension .csv
- Import into RePhase (need to change the drop-down to "all files" instead of .txt/.frd)

CSV seems to work well across platforms, so I'd try that with Smaart.

Chris
Logged
Sheffield-based sound engineering.
www.grimshawaudio.com

Michael Lawrence

  • Full Member
  • ***
  • Offline Offline
  • Posts: 144
Re: Eclipse Audio FIR Designer
« Reply #22 on: December 19, 2021, 09:43:18 AM »

CSV seems to work well across platforms, so I'd try that with Smaart.

Smaart import / export used to be a grab bag of CSV and TSV (tab separated) in various parts of the program. As of v8.5 everything is tab separated. Some parts of the world use a comma in place of a decimal in measurement data which causes all hell to break loose if you then try to import or export that data as a CSV.
Logged

Chris Grimshaw

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1740
  • Sheffield, UK
    • Grimshaw Audio
Re: Eclipse Audio FIR Designer
« Reply #23 on: December 20, 2021, 02:02:28 AM »

Good point about the decimals!
Just tried REW with a tab delimiter. Saved as a .txt file and RePhase picked it up without issue.

I'll swap over to tab separated from here. Thanks!

Chris
Logged
Sheffield-based sound engineering.
www.grimshawaudio.com

Helge A Bentsen

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1330
  • Oslo, Norway.
Re: Eclipse Audio FIR Designer
« Reply #24 on: January 08, 2022, 08:56:40 AM »

Went back and redid my measurements yesterday.
Tried locating acoustic center for all pass bands and ended up with the horn driver over my rotating turntable center (roughly).

Also time-aligned the passbands first before measured them. This gave a very consistent phase response (as in roughly the same change) in all pass bands when I rotated it. Loaded the measurements into FIR Designer, the processed response looks more even now across the horisontal plane.

Next step is buing the software and measure/listen to the actual response.
Logged

Helge A Bentsen

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1330
  • Oslo, Norway.
Re: Eclipse Audio FIR Designer
« Reply #25 on: January 12, 2022, 03:42:58 PM »

Bought the software, did a couple of different FIRs for the speaker I'm testing and its sounds and measures pretty promising.
But, the LF section is a bit low in gain. Not a big issue, I can run it hotter in Armonia, but I noticed that there is an option for boosting the whole FIR filter in level before exporting it from Fir Designer.
Is there any reason not to boost it before export?
Could you clip the filter in any way?

We're taking about roughly 6dB.
Logged

Chris Grimshaw

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1740
  • Sheffield, UK
    • Grimshaw Audio
Re: Eclipse Audio FIR Designer
« Reply #26 on: January 13, 2022, 09:01:46 AM »

I made an FIR file that's just a 6dB boost across the range. Armonia+ seemed happy with it.

I'm not an expert on DSP (just someone that likes messing with it), but I'd guess it gets lumped into the overall processing (including the output level fader). With 32-bit floating point processing, I don't think you're in any danger of digital clipping.

Chris
Logged
Sheffield-based sound engineering.
www.grimshawaudio.com

Mark Wilkinson

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1070
Re: Eclipse Audio FIR Designer
« Reply #27 on: January 14, 2022, 08:43:24 AM »

Bought the software, did a couple of different FIRs for the speaker I'm testing and its sounds and measures pretty promising.
But, the LF section is a bit low in gain. Not a big issue, I can run it hotter in Armonia, but I noticed that there is an option for boosting the whole FIR filter in level before exporting it from Fir Designer.
Is there any reason not to boost it before export?
Could you clip the filter in any way?

We're taking about roughly 6dB.

FirD has a warning pop up on the export page if the FIR file has digital clipping.
As shown below, but your version of FirD might have the warning in some place different on the screen (mine is an older version).

Usually, it's only HF/VHF files that are ever in any danger of digital clipping, with their taller impulse responses.
A sub for example, with its very short impulse response can take the maximum allowed output boost (30dB in my version), and still not be close to clipping.

I often adjust output gains on export to level match across driver sections , so i don't have to adjust gains elsewhere, like in the amp or processor.
Logged

Helge A Bentsen

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1330
  • Oslo, Norway.
Re: Eclipse Audio FIR Designer
« Reply #28 on: January 15, 2022, 05:52:28 AM »

FirD has a warning pop up on the export page if the FIR file has digital clipping.
As shown below, but your version of FirD might have the warning in some place different on the screen (mine is an older version).

Usually, it's only HF/VHF files that are ever in any danger of digital clipping, with their taller impulse responses.
A sub for example, with its very short impulse response can take the maximum allowed output boost (30dB in my version), and still not be close to clipping.

I often adjust output gains on export to level match across driver sections , so i don't have to adjust gains elsewhere, like in the amp or processor.

Thanks.
I'm thinking about doing the same thing, adjust output gain on export to keep the gains in Armonia at a fixed dB.

Logged

ProSoundWeb Community

Re: Eclipse Audio FIR Designer
« Reply #28 on: January 15, 2022, 05:52:28 AM »


Pages: 1 2 [3]   Go Up
 



Site Hosted By Ashdown Technologies, Inc.

Page created in 0.028 seconds with 22 queries.