ProSoundWeb Community

Please login or register.

Login with username, password and session length
Advanced search  

Pages: [1]   Go Down

Author Topic: Interesting B&C Single 21 with Dual 18 IB sub  (Read 809 times)

Caleb Dueck

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1449
Re: Interesting B&C Single 21 with Dual 18 IB sub
« Reply #1 on: August 06, 2021, 09:37:02 PM »

https://www.bcspeakers.com/media/W1siZiIsIjIwMjEvMDgvMDYvMTZfMDlfMjRfMTQ5X1MyMUlCLnppcCJdXQ

If one of the driving forces of DIY is SPL per dollar - once you add up the hefty driver cost and amplifier cost - how does that skew the equation? 

Otherwise - looks impressive, and small.
Logged
Experience is something you get right after you need it.

Helge A Bentsen

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1254
  • Oslo, Norway.
Re: Interesting B&C Single 21 with Dual 18 IB sub
« Reply #2 on: August 07, 2021, 02:48:24 AM »

Amp cost shouldn't be that bad, you can run it as one/two or three channels.
I suspect this sub has a fair chance of reaching it's stated SPL and still sound good. That alone would offset the driver cost for me.
Add inn the 215-DCX they released a day earlier, and you can build a pretty serious PA.
Logged

Chris Grimshaw

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
  • Sheffield, UK
    • Grimshaw Audio
Re: Interesting B&C Single 21 with Dual 18 IB sub
« Reply #3 on: August 07, 2021, 09:24:24 AM »

Interesting cabinet design - not a typical approach, that's for sure.

My gut reaction is that the 21" cone in a small enclosed space will have trouble getting rid of heat from the motor. There's also the mis-match in cone areas between the 2x18" vs 1x21". I suspect that it could lower distortion to a point (the 2x18"s pushing the 21" cone a bit further when the 21" cone itself is starting to get non-linear - perhaps), but the overall limiting factor will still be how much air the 21" cone can move.

Since B&C (who make excellent drivers) have published this design, I'd certainly be interested to try it out.

Chris
Logged
Sheffield-based sound engineering.
www.grimshawaudio.com

Tim McCulloch

  • SR Forums
  • Hero Member
  • *
  • Offline Offline
  • Posts: 22189
  • Wichita, Kansas USA
Re: Interesting B&C Single 21 with Dual 18 IB sub
« Reply #4 on: August 07, 2021, 06:36:43 PM »

Maybe we could get Bennett Prescott to explain it?
Logged
"Practicing an art, no matter how well or badly, is a way to make your soul grow, for heaven's sake. Sing in the shower. Dance to the radio. Tell stories. Write a poem to a friend, even a lousy poem. Do it as well as you possible can. You will get an enormous reward. You will have created something."  - Kurt Vonnegut

Ales Dravinec

  • Newbie
  • *
  • Offline Offline
  • Posts: 43
  • ADRaudio, Slovenia
Re: Interesting B&C Single 21 with Dual 18 IB sub
« Reply #5 on: August 09, 2021, 05:02:09 AM »

Interesting cabinet design - not a typical approach, that's for sure.

My gut reaction is that the 21" cone in a small enclosed space will have trouble getting rid of heat from the motor. There's also the mis-match in cone areas between the 2x18" vs 1x21". I suspect that it could lower distortion to a point (the 2x18"s pushing the 21" cone a bit further when the 21" cone itself is starting to get non-linear - perhaps), but the overall limiting factor will still be how much air the 21" cone can move.

Since B&C (who make excellent drivers) have published this design, I'd certainly be interested to try it out.

Chris

Chris, your gut reaction is exactly spot on ! Heat from 21" motor can be an issue with prolonged use. That is why two smaller holes are there on internal walls.
For 'lighter' use those holes may be omitted, dropping THD even more.
Your explanation of cone areas miss-match is EXACTLY right. THD at higher SPLs is dramatically reduced, which puts this design very high in 'clean sub' competition.
.
.
Please don't ask me how I know ...

With utmost respect
Logged

Tim McCulloch

  • SR Forums
  • Hero Member
  • *
  • Offline Offline
  • Posts: 22189
  • Wichita, Kansas USA
Re: Interesting B&C Single 21 with Dual 18 IB sub
« Reply #6 on: August 09, 2021, 03:32:47 PM »

Greetings, Ales!  Good to see you posting here. :)
Logged
"Practicing an art, no matter how well or badly, is a way to make your soul grow, for heaven's sake. Sing in the shower. Dance to the radio. Tell stories. Write a poem to a friend, even a lousy poem. Do it as well as you possible can. You will get an enormous reward. You will have created something."  - Kurt Vonnegut

Art Welter

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1939
Re: Interesting B&C Single 21 with Dual 18 IB sub
« Reply #7 on: August 13, 2021, 03:04:17 PM »


Please don't ask me how I know ...

With utmost respect
Ales,

As the designer, I'd guess you would know ;^)
Good work!

"Cool" impedance curve, above 6 ohms at Fb with three parallel 8 ohm woofers,  that's something you don't see every day! 
What voltage was used for the CEA2010B tone burst test?
How much voltage before the 21" hits Xmech in the 45-50 Hz range?

Art


Logged

Ales Dravinec

  • Newbie
  • *
  • Offline Offline
  • Posts: 43
  • ADRaudio, Slovenia
Re: Interesting B&C Single 21 with Dual 18 IB sub
« Reply #8 on: August 16, 2021, 03:15:01 AM »

Ales,

As the designer, I'd guess you would know ;^)
Good work!

"Cool" impedance curve, above 6 ohms at Fb with three parallel 8 ohm woofers,  that's something you don't see every day! 
What voltage was used for the CEA2010B tone burst test?
How much voltage before the 21" hits Xmech in the 45-50 Hz range?

Art

Art,
Recalling it right, I did not pass 100V rms. I used Powersoft X8 for its tremendous capabilities.
I'd say 80V rms was limiting voltage for reaching mechanical 'end'. Above that the 'low THD' statement doesn't stand, of course.
To be honest, I was rather surprised about impedance curve when originally designing this unit. Fb is under 30Hz (looking at original graph now being 25.4 Hz), which was designed for.
But the second peak at 50Hz I simply can not explain. Please forgive me.
Lowest impedance is at approximately 110Hz (2.5 ohms), while the highest sits at Fb 25.4 Hz being around 12 ohms. Ratio between the two is rather shocking being so small.
.
.
One more secret about this design :
I originally wanted to design an isobaric subwoofer WITHOUT removable wooden panels.
The only way to do this is to use smaller back drivers that would fit through front driver hole ....
All that happened later was just a bunch of new things : responses, impedances, ... But mostly ... somebody turned off THD ... go figure.

I think it would be better that somebody knowledgable tries to model and explain why that is. Phil or Dave or Tom come to my mind.

Respectfully !
Logged

Art Welter

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1939
Re: Interesting B&C Single 21 with Dual 18 IB sub
« Reply #9 on: August 16, 2021, 04:41:05 PM »

Art,
Recalling it right, I did not pass 100V rms. I used Powersoft X8 for its tremendous capabilities.
I'd say 80V rms was limiting voltage for reaching mechanical 'end'. Above that the 'low THD' statement doesn't stand, of course.
To be honest, I was rather surprised about impedance curve when originally designing this unit. Fb is under 30Hz (looking at original graph now being 25.4 Hz), which was designed for.
Ales,

All "normal" bass reflex cabinets have both the impedance and cone excursion minima at Fb, like Josh Ricci's 25Hz Fb B&C 21SW152 similar sized design.
I assumed an isobaric would be the same, but your design using three drivers of two different types appears to be quite different in impedance response.
Makes me wonder if the excursion minima of the 21" and 18" match, or the chamber between results in different excursion for either.
Did you measure cone excursion and find the minima at 25.4 Hz rather than the lower passband impedance minima around 35Hz?

Art
« Last Edit: August 17, 2021, 02:42:48 PM by Art Welter »
Logged

ProSoundWeb Community

Re: Interesting B&C Single 21 with Dual 18 IB sub
« Reply #9 on: August 16, 2021, 04:41:05 PM »


Pages: [1]   Go Up
 



Site Hosted By Ashdown Technologies, Inc.

Page created in 0.035 seconds with 19 queries.