ProSoundWeb Community

Please login or register.

Login with username, password and session length
Advanced search  

Pages: [1]   Go Down

Author Topic: Basic Meyer Software Questions  (Read 573 times)

David Sturzenbecher

  • Hero Member
  • *****
  • Online Online
  • Posts: 1717
  • So. Dak.
    • Sturz Audio
Basic Meyer Software Questions
« on: June 09, 2020, 04:59:14 pm »

With the Meyer Compass Software, do you have to be connected to actual equipment to do anything?   If I show the Galileo tab, add a processor, I can see the grayed out settings, but even in "virtual" mode they are grayed out. Likewise with the CAL tab...all grayed out controls.
Logged
Audio Systems Design Engineer
Daktronics, Inc.
CTS-D, CTS-I
AES Full Member

John Sulek

  • Sr. Member
  • ****
  • Offline Offline
  • Posts: 464
  • Toronto Canada
Re: Basic Meyer Software Questions
« Reply #1 on: June 09, 2020, 05:43:16 pm »

With the Meyer Compass Software, do you have to be connected to actual equipment to do anything?   If I show the Galileo tab, add a processor, I can see the grayed out settings, but even in "virtual" mode they are grayed out. Likewise with the CAL tab...all grayed out controls.
You do not need to be connected to any physical hardware.
Under the "devices" tab, click on the "use virtual" button of the device you have added that you wish to program. It should show "connected" after a short pause. Then you are set to start programming.
Logged

David Sturzenbecher

  • Hero Member
  • *****
  • Online Online
  • Posts: 1717
  • So. Dak.
    • Sturz Audio
Re: Basic Meyer Software Questions
« Reply #2 on: June 09, 2020, 05:51:08 pm »

You do not need to be connected to any physical hardware.
Under the "devices" tab, click on the "use virtual" button of the device you have added that you wish to program. It should show "connected" after a short pause. Then you are set to start programming.

Hi John,
Thanks for the reply.  When i click "Use Virtual" it says ERROR in that block, and the Connecting and Status field just say "connecting".  Weird.
Logged
Audio Systems Design Engineer
Daktronics, Inc.
CTS-D, CTS-I
AES Full Member

John Sulek

  • Sr. Member
  • ****
  • Offline Offline
  • Posts: 464
  • Toronto Canada
Re: Basic Meyer Software Questions
« Reply #3 on: June 09, 2020, 07:03:59 pm »

Hi John,
Thanks for the reply.  When i click "Use Virtual" it says ERROR in that block, and the Connecting and Status field just say "connecting".  Weird.
Hmmm. I just tried it again on Compass. Deleted all the virtual Galileo devices already there, added one and connected and disconnected a few times with the "use virtual " button.
It has been a while since I used this software regularly, but I don't remember any problems using the offline editor.
Sorry I can't point to the problem.
Logged

Matthias McCready

  • Sr. Member
  • ****
  • Offline Offline
  • Posts: 255
Re: Basic Meyer Software Questions
« Reply #4 on: June 09, 2020, 09:46:46 pm »

Hi John,
Thanks for the reply.  When i click "Use Virtual" it says ERROR in that block, and the Connecting and Status field just say "connecting".  Weird.

Do you need to be logged in? I know in MAPP that is a thing.
Logged
Measure twice, and cut once; this is especially important if you are a mohel.

David Sturzenbecher

  • Hero Member
  • *****
  • Online Online
  • Posts: 1717
  • So. Dak.
    • Sturz Audio
Re: Basic Meyer Software Questions
« Reply #5 on: June 10, 2020, 08:55:49 am »

Hmmm. I just tried it again on Compass. Deleted all the virtual Galileo devices already there, added one and connected and disconnected a few times with the "use virtual " button.
It has been a while since I used this software regularly, but I don't remember any problems using the offline editor.
Sorry I can't point to the problem.

Hi John,
Deleting all the Galileo devices already there, then adding one back in seems to have done the trick.  Weird, but thanks again.
Logged
Audio Systems Design Engineer
Daktronics, Inc.
CTS-D, CTS-I
AES Full Member

ProSoundWeb Community

Re: Basic Meyer Software Questions
« Reply #5 on: June 10, 2020, 08:55:49 am »


Pages: [1]   Go Up
 



Page created in 0.054 seconds with 24 queries.