ProSoundWeb Community

Please login or register.

Login with username, password and session length
Advanced search  

Pages: 1 [2]  All   Go Down

Author Topic: Causes of high latency in Digital Radios and Comms  (Read 1141 times)

Ike Zimbel

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 568
  • I'm not a newbie, I just play one on the internet!
    • Zimbel Audio Productions
Re: Causes of high latency in Digital Radios and Comms
« Reply #10 on: October 29, 2019, 11:29:29 am »

I agree...Digital radios should NEVER be used in a production environment.
Hear! Hear! Or, I wish I could hear. They sound like crap, the intelligibility is terrible, and turning them up does not make them more intelligible. I've also noticed that in venues like arenas, stadiums, ballrooms etc. that most of the venue staff (cooks, cleaners etc.) often have their radios on their belt and turned up to full volume. Lots of fun when you happen to find yourself in an elevator with these folks... :'(
Logged
~Ike Zimbel~
Wireless frequency coordination specialist.
Manufacturer's Representative (Canada)

Radio Active Designs
~416-720-0887~
ca.linkedin.com/pub/ike-zimbel/48/aa1/266

Pete Erskine

  • Moderator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1385
    • Best Audio
Re: Causes of high latency in Digital Radios and Comms
« Reply #11 on: October 29, 2019, 12:13:45 pm »

Isn't the BTR-800 E88 band still legal in North America? :)

-Russ

Yes however it is soon to be discontinued...and it's a terrible band anyway.
Logged
Pete Erskine
917-750-1134
www.bestaudio.com
peter@bestaudio.com

Henry Cohen

  • Moderator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 989
  • Westchester Co., NY, USA
Re: Causes of high latency in Digital Radios and Comms
« Reply #12 on: October 29, 2019, 01:09:11 pm »

I disagree.  On a tour there are often many radios in the same physical space.  Were replaced all our analog radios with CP200D a few years ago and the delay is maddening when someone walks into the production office or the crew is talking on the deck. 

I was referring to the real world of LMR deployments and workflows; not the micro-niche market that is entertainment production.
Logged
Henry Cohen

CP Communications    www.cpcomms.com
Radio Active Designs   www.radioactiverf.com

Henry Cohen

  • Moderator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 989
  • Westchester Co., NY, USA
Re: Causes of high latency in Digital Radios and Comms
« Reply #13 on: October 29, 2019, 01:12:09 pm »

I agree...Digital radios should NEVER be used in a production environment.

When ordering radios from a vendor (for either rental or purchase), order all simplex channels programmed in analog mode. Additionally, if there's only one repeater channel on the radio, that too can be ordered as analog. The only time you must run in digital mode is when there are multiple repeater channels.
Logged
Henry Cohen

CP Communications    www.cpcomms.com
Radio Active Designs   www.radioactiverf.com

brian maddox

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2500
  • HeyYahWon! ttsss! ttsss!
Re: Causes of high latency in Digital Radios and Comms
« Reply #14 on: October 29, 2019, 03:44:23 pm »

I agree...Digital radios should NEVER be used in a production environment.

The "push the button and then wait for the chirp to talk" aspect is enough to make me want to throw the things across the room.

But then Half-Duplex makes me crazy in and of itself.  I remember when the Nextel phones first came out and everyone was raving about the whole PTT feature and i was like "we've got Full Duplex PHONES - Why would we EVER go back to glorified radios????"
Logged
"It feels wrong to be in the audience.  And it's too peopley!" - Steve Smith

brian maddox
bdmaudio@gmail.com

'...do not trifle with the affairs of dragons...

       ....for you are crunchy, and taste good with ketchup...'

Scott Holtzman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5951
  • Ghost AV - Avon Lake, OH
    • Ghost Audio Visual Systems, LLC
Re: Causes of high latency in Digital Radios and Comms
« Reply #15 on: October 29, 2019, 09:50:06 pm »

The "push the button and then wait for the chirp to talk" aspect is enough to make me want to throw the things across the room.

But then Half-Duplex makes me crazy in and of itself.  I remember when the Nextel phones first came out and everyone was raving about the whole PTT feature and i was like "we've got Full Duplex PHONES - Why would we EVER go back to glorified radios????"

Interesting note about PTT emulation.  I worked for Winphoria networks out of Boston (who was later purchased by Motorola, what a win for us who came to work at the little startup) they were a bunch of Bell Labs guys who had designed the first softswitch for land mobile use.  They were having a hard time convincing the cellular folks that a few racks of servers could replace 100 cabinets of switching gear and the VC money was burning.  Verizon was absolutely up in arms over how to compete with Sprint who had purchased Nextel and was marketing the crap out of PTT services. 

This is actually even more interesting because the whole reason the IDEN PTT mode was on the Nextel phones is they purchased 800Mhz land mobile licenses where interconnect is a secondary server to dispatch (2 way radio) so the PTT mode was added for legal reasons.  It was immensely popular and Verizon took notice of this. 

Guru Pi the CTO of Winphoria was a brilliant dude and he re-purposed our softswitch to provide a PTT expereince over 1xRTT cellular data networks.  Our switching nodes were located in the Verizon CO's right next to the data frame for no latency.  While latency surely was an issue so was call setup time so they had to keep the data connection up that trashed battery life.  The first PTT phones were less than stellar.  Side note I bet the coming low latency 5G will finally making emulating a 2 way radio on a WAN tolerable.

Finishing the story, I had gotten the job with Winphoria because they were installing one of these nodes and software geniuses don't know how to read Bell Telephone installation guidelines.  Between almost blowing up a -48V BDFB, not isolating the rack from the floor etc. they did not get a warm reception.  I never even saw our offices the first 2 months of my job.  I was hired and flew straight to Verizon Engineering HQ in Bedminster NJ. 

That project was never commercially successful however I earned tremendous respect for the Verizon Wireless engineering team and their quest for excellence.   I spend 6 more years with Motorola until the Galvin's lost control of the company and I left to pursue my ISP full time.  Never would have gotten back into the production world if it wasn't for this odd chain of events.

A little history on IDEN, Cellular and PTT. 

What I need to do is obtain an itinerant part 90 license and build a little repeater for production.  This conversation has reminded me that I wanted to upgrade our crappy FRS UHF radios. 

 
Logged
Scott AKA "Skyking" Holtzman

Ghost Audio Visual Solutions, LLC
Cleveland OH
www.ghostav.rocks

Pete Erskine

  • Moderator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1385
    • Best Audio
Re: Causes of high latency in Digital Radios and Comms
« Reply #16 on: October 29, 2019, 09:52:58 pm »

The "push the button and then wait for the chirp to talk" aspect is enough to make me want to throw the things across the room.

But then Half-Duplex makes me crazy in and of itself.  I remember when the Nextel phones first came out and everyone was raving about the whole PTT feature and i was like "we've got Full Duplex PHONES - Why would we EVER go back to glorified radios????"

Depends on what you are doing with them.  Traffic movement, logistics OK.  Calling cues and trouble shooting no.  I was on a gig with intense IT.  $ people were setting it up and making adjustments...they got so frustrated with radios that the show was beginning to suffer.  I had 4 Crewcom full duplex beltpacks extra and gave them to that crew and the difference was amazing.
Logged
Pete Erskine
917-750-1134
www.bestaudio.com
peter@bestaudio.com

Andrew Broughton

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1714
    • Check Check One Two
Re: Causes of high latency in Digital Radios and Comms
« Reply #17 on: October 30, 2019, 07:13:35 pm »

Thanks, everyone.

So is the consensus that digital walkie-talkies COULD be made to have low latency and instant-PTT but it's just not a priority? After all, there's digital wireless microphones with high quality audio and low latency, so you'd think it would be a breeze to do even better with the (relatively) low fidelity/bandwidth requirements of walkie-talkies. It's not like "quality" digital radios are cheap or anything!
Logged
-Andy

"Well, my days of not taking you seriously are certainly coming to a middle..."

http://www.checkcheckonetwo.com
Saving lives through Digital Audio, Programming and Electronics.

Jason Glass

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 757
    • CleanWirelessAudio.com
Re: Causes of high latency in Digital Radios and Comms
« Reply #18 on: October 30, 2019, 08:54:44 pm »

Thanks, everyone.

So is the consensus that digital walkie-talkies COULD be made to have low latency and instant-PTT but it's just not a priority? After all, there's digital wireless microphones with high quality audio and low latency, so you'd think it would be a breeze to do even better with the (relatively) low fidelity/bandwidth requirements of walkie-talkies. It's not like "quality" digital radios are cheap or anything!

No. Cramming intelligible vocal audio into 6.25 kHz of mandated RF channel bandwidth requires extreme data compression, and that compression takes processing time.

Microphones have 200 kHz of channel bandwidth to work with.  It still takes time, but less time.  With hardware a fraction of the size of walkies.

Both scenarios are also within the constraints of power consumption vs. battery size and mass vs. TX power.

The math works out, until the next RF tech breakthrough.

ProSoundWeb Community

Re: Causes of high latency in Digital Radios and Comms
« Reply #18 on: October 30, 2019, 08:54:44 pm »


Pages: 1 [2]  All   Go Up
 



Page created in 0.053 seconds with 25 queries.