ProSoundWeb Community

Please login or register.

Login with username, password and session length
Advanced search  

Pages: 1 2 [3]   Go Down

Author Topic: QSC PLD4.5 vs PL380 on subs  (Read 1429 times)

Caleb Dueck

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 921
Re: QSC PLD4.5 vs PL380 on subs
« Reply #20 on: August 14, 2019, 10:54:30 am »

Interesting comparison.  It should be expected for the 4.5s to outperform the pl380s in 8 ohms, they're rated quite a bit higher.

We use PLX amps on our main tops at the moment and have been very happy.  We have not yet experienced the resetting issue you mention although I have heard about it from others.  I would totally swap them for PLDs for the DSP and flexiblity but many class D amps I have heard on highs sound overly harsh, I was worried the PLDs would suffer the same issue so I have avoided them for tops.
Do you notice a harshness?

It's a bit unfair to lump all class D amps together.  It's a fairly mature technology with many sub-variants, some of which sound worse than others. 

It would be fun to compare the newest generation of Powersoft, Linea, Lab, PKN, Crown, Yamaha, Camco, and d&b on the same speakers.  My guess is there is more difference between cheap and expensive than "good D" vs H. 
Logged
Experience is something you get right after you need it.

Tim Weaver

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2189
  • College Station, Texas
    • Daniela Weaver Photography
Re: QSC PLD4.5 vs PL380 on subs
« Reply #21 on: August 14, 2019, 11:51:59 am »

Miller Pro Audio bought a bunch of PLD amps for their subs and quickly had a lot of amp failures when the amps were loaded down. After about a year they abandoned the PLD for sub duty and went back to anything but. Now, you may not be driving your rig as hard as they do, so the PLD may be OK, but just know when the going gets tough the PLD often gives up.

They have been fantastic in all other roles. For tops, monitor, SOS, etc. Just not driven hard on subs.

To be fair, these amps are asked to deal with 100 degree ambient emps in dusty, dirty, humid, sometimes rainy conditions often loaded down to 2 ohms per channel. So not light duty use at all. YMMV
Logged
Bullwinkle: This is the amplifier, which amplifies the sound. This is the Preamplifier which, of course, amplifies the pree's.

Robert Healey

  • Full Member
  • ***
  • Offline Offline
  • Posts: 224
Re: QSC PLD4.5 vs PL380 on subs
« Reply #22 on: August 14, 2019, 11:57:24 am »

Miller Pro Audio bought a bunch of PLD amps for their subs and quickly had a lot of amp failures when the amps were loaded down. After about a year they abandoned the PLD for sub duty and went back to anything but. Now, you may not be driving your rig as hard as they do, so the PLD may be OK, but just know when the going gets tough the PLD often gives up.

There were some initial problems with the PLD/CXD amps that QSC fixed with firmware, and in some cases, hardware updates.

Bob Lee describes it in this thread: https://forums.prosoundweb.com/index.php/topic,157135.10.html
Logged

Mark Wilkinson

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 882
Re: QSC PLD4.5 vs PL380 on subs
« Reply #23 on: August 14, 2019, 02:34:53 pm »

I know i said in an earlier post, that I'd choose a PLD4.5 over a PL380 for the flexibility....and the fact that if I'm close to driving my subs to the full output of the PLD, I should probably be thinking about getting more subs than more amp..

However, having said that.....if I knew the amp was only going to be used for subs, there is zero question in my mind that the PL380 is the better sub amp.
Just like everyone has said....

Justin...where did you get the PLDs are rated higher at 8 ohms? Published specs I've seen say PL380 has 1500W, and PLD4.5 has 1150W.
Those specs match measurements I've made of the amps under an 8 ohm load  (when trying to learn limiters)
Logged

Justin Quinn

  • Newbie
  • *
  • Offline Offline
  • Posts: 8
Re: QSC PLD4.5 vs PL380 on subs
« Reply #24 on: August 15, 2019, 08:32:09 pm »

I know i said in an earlier post, that I'd choose a PLD4.5 over a PL380 for the flexibility....and the fact that if I'm close to driving my subs to the full output of the PLD, I should probably be thinking about getting more subs than more amp..

However, having said that.....if I knew the amp was only going to be used for subs, there is zero question in my mind that the PL380 is the better sub amp.
Just like everyone has said....

Justin...where did you get the PLDs are rated higher at 8 ohms? Published specs I've seen say PL380 has 1500W, and PLD4.5 has 1150W.
Those specs match measurements I've made of the amps under an 8 ohm load  (when trying to learn limiters)
My mistake, thank you for pointing this out.  I was replying to this from Brian
When I got the PLD 4.5's, they replaced PLX 3602's.  Into an 8 ohm load in 4 channel mode, the amps ran circles around the 3602's.  When in 4 ohm at 4 channels, they seemed pretty comparable, although I rarely used them in that configuration.
In which he was comparing the PLD4.5s to the PLX3602.  When I said the "PL380's" were rated lower in 8 ohms I actually meant the PLX3602's (725W X 2 @ 8ohms) which are, in fact, rated lower per channel in 8 ohms.

My mistake.
Logged

Dan Richardson

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 585
  • southern Vermont
    • NotTooLoud
Re: QSC PLD4.5 vs PL380 on subs
« Reply #25 on: August 16, 2019, 08:37:53 am »

Does anyone here have experience as to how Peavey's IPR2 7500 would compare to these on sub duty?
Logged
The best sound system is no sound system. Everything else is compromise.
Pages: 1 2 [3]   Go Up
 


Page created in 0.041 seconds with 21 queries.