ProSoundWeb Community

Please login or register.

Login with username, password and session length
Advanced search  

Pages: 1 2 [All]   Go Down

Author Topic: Best way to do a transfer function of an amplifier output?  (Read 6214 times)

John Penkala

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 510
Best way to do a transfer function of an amplifier output?
« on: June 18, 2018, 02:29:40 PM »

I'd like to do a transfer function of an amplifiers output to "see the processing". How are folks padding down the output of the amplifier to a level that a USB I/O can handle? Any help is appreciated.

JP
Logged

Nathan Riddle

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2045
  • Niceville, FL
    • Nailed Productions
Re: Best way to do a transfer function of an amplifier output?
« Reply #1 on: June 18, 2018, 02:46:15 PM »

You can connect it directly, just don't exceed 24v or so (for an interface with line level inputs) :P

(I've done it, just be careful of the gain knob ;) )

Any *nearly voltage divider will work though.
http://www.epanorama.net/circuits/speaker_to_line.html/

If you really don't want to blow up your equipment then isolated transformer is best way to go.

If you want to run the amp (depends on max voltage) into clipping then you'd need higher value resistors and wattage.

good luck have fun!
Logged
I'm just a guy trying to do the next right thing.

This business is for people with too much energy for desk jobs and too much brain for labor jobs. - Scott Helmke

Ivan Beaver

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 9533
  • Atlanta GA
Re: Best way to do a transfer function of an amplifier output?
« Reply #2 on: June 23, 2018, 02:09:55 PM »

I built a box that has a pad on the amplifier output, then that goes into an old Altec line level transformer.

The main reason for the transformer is to provide physical isolation between the amp and the interface input.

This way you can look at bridged outputs, or amps that have both output terminals floating.

Be sure to use a high quality transformer to avoid saturation.

The pad size will depend on the size of the amp being looked at.  But if you calculate it to get to around a -10dBu or so, the transformer should be fine.

Or you can simply turn the amp down.

It all depends on exactly what you are trying to measure and why.

BTW I use this method when setting up/matching transfer functions of amps with DSPs in them.
Logged
A complex question is easily answered by a simple-easy to understand WRONG answer!

Ivan Beaver
Danley Sound Labs

PHYSICS- NOT FADS!

David Sturzenbecher

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1966
  • So. Dak.
    • Sturz Audio
Re: Best way to do a transfer function of an amplifier output?
« Reply #3 on: June 23, 2018, 03:43:09 PM »

I have always used the VIbox from linearX in the past with great success. Unfortunately they are no longer available due to the passing of the companies owner.


Sent from my iPhone using Tapatalk Pro
Logged
Audio Systems Design Engineer
Daktronics, Inc.
CTS-D, CTS-I
AES Full Member

Hayden J. Nebus

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 637
  • Richmond, VA
Re: Best way to do a transfer function of an amplifier output?
« Reply #4 on: July 18, 2018, 05:39:50 PM »

I'd like to do a transfer function of an amplifiers output to "see the processing". How are folks padding down the output of the amplifier to a level that a USB I/O can handle? Any help is appreciated.

JP

Most DSP amps have some sort of handle to turn it down, just turn it down by about 30dB. Stim near -20dBfs/0dBu and you should be well above the noise floor still and near unity gain.
Logged

Lyle Williams

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1558
Re: Best way to do a transfer function of an amplifier output?
« Reply #5 on: August 01, 2018, 11:57:43 AM »

You really should have a dummy load that can handle full amp output (some great heatsunk monster) and have a voltage divider across that.

But the result will be very very flat.  If there is DSP it will be textbook-perfect EQ and resulting phase shift.
Logged

Ivan Beaver

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 9533
  • Atlanta GA
Re: Best way to do a transfer function of an amplifier output?
« Reply #6 on: August 01, 2018, 07:01:33 PM »

You really should have a dummy load that can handle full amp output (some great heatsunk monster) and have a voltage divider across that.

But the result will be very very flat.  If there is DSP it will be textbook-perfect EQ and resulting phase shift.
With solid state amps you don't need to put a load on it.
Logged
A complex question is easily answered by a simple-easy to understand WRONG answer!

Ivan Beaver
Danley Sound Labs

PHYSICS- NOT FADS!

Justin Segbers

  • Newbie
  • *
  • Offline Offline
  • Posts: 5
Re: Best way to do a transfer function of an amplifier output?
« Reply #7 on: August 13, 2018, 03:13:46 PM »

I'd like to do a transfer function of an amplifiers output to "see the processing". How are folks padding down the output of the amplifier to a level that a USB I/O can handle? Any help is appreciated.

JP

Put a countryman Di with it selected to speaker input.  May not be perfectly flat? but I had no issues reverse engineering some l'acoustics presets to load them onto some crown amps for some extra rental flexibility.
Logged

Chris Grimshaw

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1822
  • Sheffield, UK
    • Grimshaw Audio
Re: Best way to do a transfer function of an amplifier output?
« Reply #8 on: October 23, 2018, 05:35:29 PM »

With solid state amps you don't need to put a load on it.

While true in theory, I think an interesting part of testing amplifiers is when you push them to the ragged edge with 2ohm (or worse) testing and see what they do.
Most amps are capable of low distortion, flat response, etc. The good ones will keep doing that when the rest have overheated and shut down.

I just wish I had a load bank capable of dissipating the multi-kilowatt power levels required.
My last load bank (some fairly big aluminium-clad resistors bolted to heatsinks) did okay until a big Crown amp got all the resistors to go open-circuit in less than 20 seconds.

Next time I'll probably just get some oil-filled electric radiators and put a few in parallel.

Chris
Logged
Sheffield-based sound engineering.
www.grimshawaudio.com

Mark Wilkinson

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1104
Re: Best way to do a transfer function of an amplifier output?
« Reply #9 on: October 23, 2018, 05:44:00 PM »


I just wish I had a load bank capable of dissipating the multi-kilowatt power levels required.

Chris

Lowes https://www.lowes.com/pd/Utilitech-Water-Heater-Screw-Element/3693202#362342

16 ohms, $6 bucks.....I just stick em, however many needed for load desired, in a 5 gal paint pail full of water...
Logged

Art Welter

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2199
  • Santa Fe, New Mexico
Re: Best way to do a transfer function of an amplifier output?
« Reply #10 on: October 23, 2018, 06:18:15 PM »

Next time I'll probably just get some oil-filled electric radiators and put a few in parallel.

Chris,

Since I already had them, used to do that, but it took 5 heaters to do a 2 ohm load, since those 1500 watt 120V heaters were about 9.6 ohms. Dragging 5 heaters to the shop was too much work, and could only test one side at two ohms.
Then I found that wrapping baling wire around a brick worked quite well, and is even cheaper than Mark W's solution, but does have some heat safety issues  ;)
IIRC, using a  8"x 3" x 2.25" brick and 16 gauge steel baling wire at about 1/4" spacing came out to 4 ohms.

Art
Logged

Mark Wilkinson

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1104
Re: Best way to do a transfer function of an amplifier output?
« Reply #11 on: October 23, 2018, 08:02:04 PM »


IIRC, using a  8"x 3" x 2.25" brick and 16 gauge steel baling wire at about 1/4" spacing came out to 4 ohms.

Art

 ;D

Did peeing on the bricks increase thermal capacity ? Lol
Logged

Art Welter

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2199
  • Santa Fe, New Mexico
Re: Best way to do a transfer function of an amplifier output?
« Reply #12 on: October 24, 2018, 01:12:58 AM »

;D

Did peeing on the bricks increase thermal capacity ? Lol
Yes, but changes the impedance too much for repeatable and reliable measurements.
Stinks like hell, too.
Logged

Frank Koenig

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1318
  • Palo Alto, CA USA
Re: Best way to do a transfer function of an amplifier output?
« Reply #13 on: October 24, 2018, 11:50:22 AM »

I've mentioned this trick before but this sounds like a good place to mention it again. You can arrange the load resistor as a voltage divider so that you can hook a speaker to the tap and hear, at a pleasant level, what the amp sounds like when it's killing itself. Since the attenuation is high the source resistance seen by the speaker is low, and all is hunky-dory. -F







Logged
"Nature abhors a vacuum tube." -- John Pierce, Bell Labs

ProSoundWeb Community

Re: Best way to do a transfer function of an amplifier output?
« Reply #13 on: October 24, 2018, 11:50:22 AM »


Pages: 1 2 [All]   Go Up
 



Site Hosted By Ashdown Technologies, Inc.

Page created in 0.043 seconds with 20 queries.