ProSoundWeb Community

Please login or register.

Login with username, password and session length
Advanced search  

Pages: [1] 2  All   Go Down

Author Topic: Suggestions for Hum  (Read 4957 times)

Paul Graves

  • Newbie
  • *
  • Offline Offline
  • Posts: 6
Suggestions for Hum
« on: August 14, 2017, 10:40:09 PM »

Our setup:

X32 and an analog mixer located in different places and different AC circuits.

Two large powered speakers with built in two channel mixer, each again different AC circuits

Impossible to get all on one or even two AC circuits.

Each mixer has its Left and Right connected to the powered speakers.

So, I am certain it is ground loop causing hum, I ran some tests connecting and disconnecting and actually I believe there are several loops. don't want to expose the equipment to risk of damage by doing something stupid.

Solutions I am considering .
1) Putting a isolation transformer each XLR cable feeding the powered speakers.
2.) Using a barrel ground lift on each XLR cable feeding the powered speakers/


Any thoughts or experience and also what would be best with our new X32 rack?

Thanks,
Paul
Logged

Debbie Dunkley

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 6037
  • Central North Carolina
Re: Suggestions for Hum
« Reply #1 on: August 14, 2017, 11:14:45 PM »

Our setup:

X32 and an analog mixer located in different places and different AC circuits.

Two large powered speakers with built in two channel mixer, each again different AC circuits

Impossible to get all on one or even two AC circuits.

Each mixer has its Left and Right connected to the powered speakers.

So, I am certain it is ground loop causing hum, I ran some tests connecting and disconnecting and actually I believe there are several loops. don't want to expose the equipment to risk of damage by doing something stupid.

Solutions I am considering .
1) Putting a isolation transformer each XLR cable feeding the powered speakers.
2.) Using a barrel ground lift on each XLR cable feeding the powered speakers/


Any thoughts or experience and also what would be best with our new X32 rack?

Thanks,
Paul

Hey Paul... heads up - change your display name to your real name as per forum rules otherwise the thread may get locked. I am sure you will get excellent suggestions from the very experienced forum members here.
Logged
A young child says to his mother, "Mom, when I grow up I'm going to be a musician." She replies, "Well honey, you know you can't do both."

Stu McDoniel

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1144
  • Central Wisconsin...USA
Re: Suggestions for Hum
« Reply #2 on: August 25, 2017, 08:41:22 AM »

Our setup:

X32 and an analog mixer located in different places and different AC circuits.

Two large powered speakers with built in two channel mixer, each again different AC circuits

Impossible to get all on one or even two AC circuits.

Each mixer has its Left and Right connected to the powered speakers.

So, I am certain it is ground loop causing hum, I ran some tests connecting and disconnecting and actually I believe there are several loops. don't want to expose the equipment to risk of damage by doing something stupid.

Solutions I am considering .
1) Putting a isolation transformer each XLR cable feeding the powered speakers.
2.) Using a barrel ground lift on each XLR cable feeding the powered speakers/


Any thoughts or experience and also what would be best with our new X32 rack?

Thanks,
Paul
You probably have a difference of potential between earth grounds or an earth ground wiring issue
on one of your circuits.   Bring in an electrician and get your earth ground situation resolved.
Forget all the work around's ideas.
Logged

Don T. Williams

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1063
  • Midas Pro 1 & 2, M32, dbTech T12, T8, S30, DM12
    • Q Systems Music & Sound
Re: Suggestions for Hum
« Reply #3 on: August 25, 2017, 11:07:46 AM »

Wasn't this thread discussed extensively in the last few weeks?  Under a different name?
Logged

Nathan Riddle

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2052
  • Niceville, FL
    • Nailed Productions
Re: Suggestions for Hum
« Reply #4 on: August 25, 2017, 11:09:59 AM »

You probably have a difference of potential between earth grounds or an earth ground wiring issue
on one of your circuits.   Bring in an electrician and get your earth ground situation resolved.
Forget all the work around's ideas.

This would be the safest and most correct way to do things and I HIGHLY encourage this.

Read this document:
http://www.rane.com/note110.html

AFTER you have read the above. Then proceed to the below solution:

If you have very little money then use these:
http://www.radialeng.com/icecube.php

Hint: there are dealers on the forum that can get you equipment for less; post in the marketplace saying: "WTB: Radial IceCube"

Here's another informational note I encourage reading! Heck, read them all :) http://www.rane.com/note151.html
Logged
I'm just a guy trying to do the next right thing.

This business is for people with too much energy for desk jobs and too much brain for labor jobs. - Scott Helmke

Ivan Beaver

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 9534
  • Atlanta GA
Re: Suggestions for Hum
« Reply #5 on: August 25, 2017, 08:12:02 PM »

Try lifting pin 1 on the SPEAKER side of the XLR.  Leave it hooked up on the send side.

That is much better than trying "fancy hum eliminators".
Logged
A complex question is easily answered by a simple-easy to understand WRONG answer!

Ivan Beaver
Danley Sound Labs

PHYSICS- NOT FADS!

g'bye, Dick Rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 7424
  • Duluth
Re: Suggestions for Hum
« Reply #6 on: August 25, 2017, 08:36:30 PM »

Wasn't this thread discussed extensively in the last few weeks?  Under a different name?

Same name, different forum section:  AV.

Sometimes when a system hums it simply means it doesn't know the words...
Logged
Pay no attention to the man behind the curtain...

Mike Caldwell

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3084
  • Covington, Ohio
    • Mike Caldwell Audio Productions
Re: Suggestions for Hum
« Reply #7 on: August 26, 2017, 08:45:39 AM »

Have you disconnected every input and every output from the mixer except the main left & right. If so did you still have hum in the system?

Kevin Graf

  • Sr. Member
  • ****
  • Offline Offline
  • Posts: 344
Re: Suggestions for Hum
« Reply #8 on: August 26, 2017, 08:55:28 AM »

The usual cause of the problem is a component with the dreaded 'pin 1 problem'.
The work-around is lifting the pin 1 shield at the receive end of the cable. You can make some short cable extensions to test that.
Logged
Speedskater

Mike Caldwell

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3084
  • Covington, Ohio
    • Mike Caldwell Audio Productions
Re: Suggestions for Hum
« Reply #9 on: August 26, 2017, 05:30:35 PM »

The usual cause of the problem is a component with the dreaded 'pin 1 problem'.
The work-around is lifting the pin 1 shield at the receive end of the cable. You can make some short cable extensions to test that.

My service call tool kit has a couple pin 1 lift short cables in it all the time as well as my production work trunk.

Another common hum source is from audio connections from video equipment/computers.
That kind of goes back to my earlier suggestion to disconnect all other input and output connections from the mixer except the mains just to help isolate and narrow down the hum source/path.

ProSoundWeb Community

Re: Suggestions for Hum
« Reply #9 on: August 26, 2017, 05:30:35 PM »


Pages: [1] 2  All   Go Up
 



Site Hosted By Ashdown Technologies, Inc.

Page created in 0.042 seconds with 25 queries.