ProSoundWeb Community

Please login or register.

Login with username, password and session length
Advanced search  

Pages: 1 ... 3 4 [5]   Go Down

Author Topic: L6-20 250v to 15a edison (Labre)  (Read 22859 times)

Jonathan Johnson

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3209
  • Southwest Washington (state, not DC)
Re: L6-20 250v to 15a edison (Labre)
« Reply #40 on: January 09, 2017, 12:45:07 PM »

Fair point.  I was making an assumption that we were looking at a US product. 

I've always enjoyed that bases are measured in mm, but lamp diameter is in 1/8ths of an inch (par38, T8)

Yes, it probably is a product made for the US market. Not necessarily US-made, though. You have to be careful when buying screw-base lamps online, as some sites may be selling an E-27 as "medium base". A little more searching I just did suggests that E-26 is typically for ~120V bulbs; E-27 for ~230V lamps. Some sites claim that E-26 and E-27 bases are interchangeable.

This page seems to do a good job of explaining the difference

Then there is my Toro zero-turn lawnmower (made in USA by Exmark, which is owned by Toro) with a Kawasaki (made in Japan) engine -- the engine is metric, but everything else on the lawnmower is SAE. I bought it (brand new) just over 3 years ago.
Logged
Stop confusing the issue with facts and logic!

Ron Ventour

  • Jr. Member
  • **
  • Offline Offline
  • Posts: 61
Re: L6-20 250v to 15a edison (Labre)
« Reply #41 on: March 02, 2019, 10:55:53 AM »

Just received a Linea Research 44m20 yesterday which is the same amp as the Danley DNA 20k4 but the power inlet is different on the LR, mines came with a 32a powercon connector.

What are my options here  plugging into 15/20 amp outlets in my house or connecting to a 50a 14-50 rac pac distro?

Any info would be greatly appreciated thanks

Sent from my SM-N950U using Tapatalk

Logged

TJ (Tom) Cornish

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4317
  • St. Paul, MN
Re: L6-20 250v to 15a edison (Labre)
« Reply #42 on: March 04, 2019, 04:45:09 PM »

Just received a Linea Research 44m20 yesterday which is the same amp as the Danley DNA 20k4 but the power inlet is different on the LR, mines came with a 32a powercon connector.

What are my options here  plugging into 15/20 amp outlets in my house or connecting to a 50a 14-50 rac pac distro?

Any info would be greatly appreciated thanks

Sent from my SM-N950U using Tapatalk
Looks like you were helped in the other thread.  In the future, starting a (single) new thread with a new question would be the most efficient way to get help, rather than tagging onto two unrelated threads.
Logged

Ron Ventour

  • Jr. Member
  • **
  • Offline Offline
  • Posts: 61
Re: L6-20 250v to 15a edison (Labre)
« Reply #43 on: March 04, 2019, 07:11:27 PM »

Looks like you were helped in the other thread.  In the future, starting a (single) new thread with a new question would be the most efficient way to get help, rather than tagging onto two unrelated threads.
yes sir

Sent from my SM-N950U using Tapatalk

Logged

ProSoundWeb Community

Re: L6-20 250v to 15a edison (Labre)
« Reply #43 on: March 04, 2019, 07:11:27 PM »


Pages: 1 ... 3 4 [5]   Go Up
 



Site Hosted By Ashdown Technologies, Inc.

Page created in 0.016 seconds with 22 queries.