ProSoundWeb Community

Please login or register.

Login with username, password and session length
Advanced search  

Pages: 1 [2]  All   Go Down

Author Topic: Not Ground Loop Hum  (Read 5166 times)

Scott Helmke

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1581
Re: Not Ground Loop Hum
« Reply #10 on: May 03, 2016, 10:13:56 am »

Would be easy enough to make a little switch/adapter dongle to use with a mic input. Change switch positions for lowest noise, then see if the switch position is in the "all wires normal" position.
Logged

Mike Sokol

  • Moderator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3360
  • Lead instructor for the No~Shock~Zone
    • No~Shock~Zone Electrical Safety
Re: Not Ground Loop Hum
« Reply #11 on: May 03, 2016, 10:38:09 am »

Would be easy enough to make a little switch/adapter dongle to use with a mic input. Change switch positions for lowest noise, then see if the switch position is in the "all wires normal" position.

I think it's easier to just open up to inspect the ends. However, your version could be used to test stage floor boxes for miswiring. I wonder just how many patch panels and floor boxes have been miswired like this?
Logged
Mike Sokol
mike@noshockzone.org
www.NoShockZone.org

Ike Zimbel

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 570
  • I'm not a newbie, I just play one on the internet!
    • Zimbel Audio Productions
Re: Not Ground Loop Hum
« Reply #12 on: May 03, 2016, 10:55:50 am »

I wonder just how many patch panels and floor boxes have been miswired like this?
Well...I know of one situation where an entire splitter / snake system had this problem. Early '90's, so details are hazy now as to whether it was the whole system or just one Mass-con snake. Discovered on a gig, of course. I also worked on a small, independent TV truck that had some tie-lines to the over-the-console rack miswired the same way. That one was painfully obvious to see how it had gone astray: The rack end was a pair of 12 channel stage-boxes bolted together, with one box being the sends (male XLR's) and the other the returns (female XLR's). Whoever wired it (and I'm sure it was a "late at night with the first gig the next day" kind of thing) had laid the boxes face down on the bench and just gone "the shields all go on the right hand pin", which was half right! The really sad thing was that this truck had been in use for a few years when I discovered this.
iz
Logged
~Ike Zimbel~
Wireless frequency coordination specialist.
Manufacturer's Representative (Canada)

Radio Active Designs
~416-720-0887~
ca.linkedin.com/pub/ike-zimbel/48/aa1/266

Steve M Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3304
  • Isle of Wight - England
Re: Not Ground Loop Hum
« Reply #13 on: May 03, 2016, 01:19:36 pm »

I recently bought some cables which had pin 3 as the ground.  I rewired mine then let the seller know.


Steve.
Logged

David Buckley

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 565
Re: Not Ground Loop Hum
« Reply #14 on: May 03, 2016, 05:04:11 pm »

Would be nice if someone integrates an LCR meter in an audio cable tester.  That way we can know if shield and hot/cold are swapped or solder connection is poor without taking cable apart.
Doesn't seem hard.  Here's a video demoing a cheap, open source component tester, based on an Arduino, that would be easy to convert into a cable tester.

I think it's easier to just open up to inspect the ends.
Or.... stick a pin through the cable jacket. 

I can't believe I just said that.


I wonder just how many patch panels and floor boxes have been miswired like this?
Last year, was the first serious user of a redone venue.  Had lots of newly-installed waylines, and every single XLR wayline was crosswired.  My theory is that they mis-wired the first wayline, then used that as the "send" line, and used a XLR cable at the far end to patch it to another wayline for testing.  Because the first one was wrong, to get the tester to show "OK" they had to miswire every other line.  Ticked the big box that said "all tested".

We complained to the venue of course, heck, I had a list of things done wrong.  I'm told the venue employed an independent contractor to watch over the installer as they re-terminated and retested each line.
« Last Edit: May 03, 2016, 05:06:56 pm by David Buckley »
Logged

Mike Sokol

  • Moderator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3360
  • Lead instructor for the No~Shock~Zone
    • No~Shock~Zone Electrical Safety
Re: Not Ground Loop Hum
« Reply #15 on: May 03, 2016, 06:25:11 pm »

Last year, was the first serious user of a redone venue.  Had lots of newly-installed waylines, and every single XLR wayline was crosswired.  My theory is that they mis-wired the first wayline, then used that as the "send" line, and used a XLR cable at the far end to patch it to another wayline for testing.  Because the first one was wrong, to get the tester to show "OK" they had to miswire every other line.  Ticked the big box that said "all tested".
As you note, the problem is that two mis-wired connectors can fool a continuity tester into passing a cable run with the shield wired pin 2 or 3. Since testing UTP CAT-5 for proper twists is pretty common and inexpensive, I wonder if there's some way to utilize that type of testing technology for XLR cables.
Logged
Mike Sokol
mike@noshockzone.org
www.NoShockZone.org

Ike Zimbel

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 570
  • I'm not a newbie, I just play one on the internet!
    • Zimbel Audio Productions
Re: Not Ground Loop Hum
« Reply #16 on: May 03, 2016, 08:55:31 pm »

As you note, the problem is that two mis-wired connectors can fool a continuity tester into passing a cable run with the shield wired pin 2 or 3. Since testing UTP CAT-5 for proper twists is pretty common and inexpensive, I wonder if there's some way to utilize that type of testing technology for XLR cables.

Hmmm...it might be as simple as a pair of XLR to RJ-45 adapters wired as one pair of the 4...but I don't have one of those testers to try it with so I'm just speculating  :-\
Logged
~Ike Zimbel~
Wireless frequency coordination specialist.
Manufacturer's Representative (Canada)

Radio Active Designs
~416-720-0887~
ca.linkedin.com/pub/ike-zimbel/48/aa1/266

Stephen Swaffer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2343
Re: Not Ground Loop Hum
« Reply #17 on: May 03, 2016, 08:56:13 pm »

The reason that mis-wiring is an issue is because noise is capacitively (I think-JR can correct me maybe inductively?) coupled to the shield.  A tester that intentionally couples a noise source to the shield should be able to identify the pin the shield is connected to-then all that is needed is a simple pin to pin continuity test.
Logged
Steve Swaffer

Mike Sokol

  • Moderator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3360
  • Lead instructor for the No~Shock~Zone
    • No~Shock~Zone Electrical Safety
Re: Not Ground Loop Hum
« Reply #18 on: May 03, 2016, 09:02:05 pm »

The reason that mis-wiring is an issue is because noise is capacitively (I think-JR can correct me maybe inductively?) coupled to the shield.  A tester that intentionally couples a noise source to the shield should be able to identify the pin the shield is connected to-then all that is needed is a simple pin to pin continuity test.
It's a little more complicated than that, since the twisted pair must be close enough together so they have the same outside noise coupling so it can be cancelled by the CMRR (Common Mode Rejection Ratio) of the balanced input circuit. 
Logged
Mike Sokol
mike@noshockzone.org
www.NoShockZone.org

John Roberts {JR}

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 16549
  • Hickory, Mississippi, USA
    • Resotune
Re: Not Ground Loop Hum
« Reply #19 on: May 04, 2016, 09:34:22 am »

The reason that mis-wiring is an issue is because noise is capacitively (I think-JR can correct me maybe inductively?) coupled to the shield.  A tester that intentionally couples a noise source to the shield should be able to identify the pin the shield is connected to-then all that is needed is a simple pin to pin continuity test.
It seems electrostatic (capacitive) coupling would be the dominant mechanism.

It "might" be as easy as measuring the capacitance between pairs of leads. I would expect the C between 2-3 to be different than 2-1 or 3-1, but this is pure speculation.

My cheap rat shack VOM has a C meter built in.

JR 
Logged
Don't tune your drums half-ass. Listen to what a properly "cleared" drum sounds like.   http://circularscience.com/

ProSoundWeb Community

Re: Not Ground Loop Hum
« Reply #19 on: May 04, 2016, 09:34:22 am »


Pages: 1 [2]  All   Go Up
 



Page created in 0.065 seconds with 23 queries.