ProSoundWeb Community

Please login or register.

Login with username, password and session length
Advanced search  

Pages: 1 [2]  All   Go Down

Author Topic: Dante interface box!  (Read 6869 times)

Pete Erskine

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1393
    • Best Audio
Re: Dante interface box!
« Reply #10 on: November 04, 2015, 11:30:26 am »

But $1,000....  I like and use Dante a bit, but $1,000 for a couple of audio I/Os...

When Dante came out with the 2x2 chip, there were hopes of "low cost" products with Dante interfaces, but I guess that's gone by the wayside.   Oh well, maybe AES67 will get the job done...
The Delec box does a lot more than just 2 I/O so $1000 is not bad.  AES I/O and GPI/O as well as headset plus fiber.

If all you want is 2 in/out analog Studio Technologies 44D is $750.00
« Last Edit: November 04, 2015, 11:33:39 am by Pete Erskine »
Logged
Pete Erskine
917-750-1134
www.bestaudio.com
peter@bestaudio.com

David Sturzenbecher

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1712
  • So. Dak.
    • Sturz Audio
Re: Dante interface box!
« Reply #11 on: November 04, 2015, 11:35:43 am »

The Delec box does a lot more than just 2 I/O so $1000 is not bad.  AES I/O and GPI/O as well as headset plus fiber.

If all you want is 2 in/out analog Studio Technologies 44D is $750.00

Just line inputs...no phantom power or mic pre's for us measurement guys
Logged
Audio Systems Design Engineer
Daktronics, Inc.
CTS-D, CTS-I
AES Full Member

Pete Erskine

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1393
    • Best Audio
Re: Dante interface box!
« Reply #12 on: November 04, 2015, 11:49:30 am »

Just line inputs...no phantom power or mic pre's for us measurement guys

Then for $625:

Model 5205 Mic/Line Input to Dante Interface (Order Code: M5205)
General-purpose audio input device for use in Dante Audio-over-Ethernet applications. The rugged, compact, and portable unit features two mic/line inputs with adjustable gain, P48 phantom power, and level metering. The unit requires an Ethernet with Power-over-Ethernet (PoE) connection to supply both the data interface as well as power.
Logged
Pete Erskine
917-750-1134
www.bestaudio.com
peter@bestaudio.com

Pete Erskine

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1393
    • Best Audio
Re: Dante interface box!
« Reply #13 on: November 04, 2015, 12:16:21 pm »

Just line inputs...no phantom power or mic pre's for us measurement guys

Or for Bare bones interface (you need to put it in a box) from Extron:

The Extron AXI 22 AT D is a single-gang Decora®-style audio interface for integrating two mic/line sources onto a Dante™-enabled DMP 128 audio system. It features two XLR audio inputs and switchable 48 volt phantom power for connecting and powering condenser microphones, plus gain controls for each input. The AXI 22 AT D also features two line outputs on the back for routing any two Dante channels from the network to an amplifier, or connecting into an optional secondary wallplate with two XLR outputs. The AXI 22 AT D interfaces with Extron Dante-equipped audio processors over a standard local area network, and can be powered through PoE. This greatly simplifies the cabling infrastructure for integrating audio connectivity in locations remote from a central equipment rack.
More info: http://www.extron.com/product/product.aspx?id=axi22atd
Logged
Pete Erskine
917-750-1134
www.bestaudio.com
peter@bestaudio.com

Scott Helmke

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1602
Re: Dante interface box!
« Reply #14 on: November 06, 2015, 03:05:29 pm »

Radio Design Labs (the folks who make all those little stick-on audio gizmos) are also doing Dante:
http://www.rdlnet.com/Dante/
Logged

David Sturzenbecher

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1712
  • So. Dak.
    • Sturz Audio
Re: Dante interface box!
« Reply #15 on: November 06, 2015, 03:40:57 pm »

Radio Design Labs (the folks who make all those little stick-on audio gizmos) are also doing Dante:
http://www.rdlnet.com/Dante/

I recently found (no idea how long they have been doing this) that Audinate is listing what appears to be all dante products in one location.

https://www.audinate.com/products/dante-enabled
Logged
Audio Systems Design Engineer
Daktronics, Inc.
CTS-D, CTS-I
AES Full Member

Cailen Waddell

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1428
Re: Dante interface box!
« Reply #16 on: November 06, 2015, 08:08:04 pm »


I recently found (no idea how long they have been doing this) that Audinate is listing what appears to be all dante products in one location.

https://www.audinate.com/products/dante-enabled

They have been doing it for quite a while...  It's handy...


Sent from my iPhone using Tapatalk
Logged

Steve Alves

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 547
  • South Florida
    • South Florida Sound
Re: Dante interface box!
« Reply #17 on: November 19, 2015, 09:45:24 am »

Logged
Steven Alves
South Florida Sound, Fort Lauderdale, FL
www.southfloridasound.com

ProSoundWeb Community

Re: Dante interface box!
« Reply #17 on: November 19, 2015, 09:45:24 am »


Pages: 1 [2]  All   Go Up
 



Page created in 0.041 seconds with 26 queries.