ProSoundWeb Community

Please login or register.

Login with username, password and session length
Advanced search  

Pages: [1]   Go Down

Author Topic: Help with setting up EV QRX/dx38/ dynacord h5000/ and cp4000s  (Read 3085 times)

Alfred Popaj

  • Newbie
  • *
  • Offline Offline
  • Posts: 4
Help with setting up EV QRX/dx38/ dynacord h5000/ and cp4000s
« on: October 02, 2013, 04:01:34 PM »

Hello everyone.  To start off here my rig.  All is being used except for the dynacord h5000.  This is for live music not dj. 

4 qrx115
2 qrx 118
dx38
2 cp4000s
1 dynacord h5000

My questions are
1. Should I keep the h5000 or is it just too much power?  The sound of the Dynacord amp sounded sweeter than the cp4000s which is causing my dilemma.
2.  If I keep it, how should i set my limiters on the dx38 so that i dont blow my tops? 
3.  If I had the dynacord on tops, i was thinking of bridging the cp4000s and using one per sub. again how should i set my limiters here without blowing them?
4.  I currently run one cp4000s for highs and one for subs, it seems like we we get close to running out of headroom most of the time, which is why im asking the above questions. 

All help would be appreciated
Logged

Scott Wagner

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1020
  • Richmond, VA
Re: Help with setting up EV QRX/dx38/ dynacord h5000/ and cp4000s
« Reply #1 on: October 02, 2013, 04:12:33 PM »

Hello everyone.  To start off here my rig.  All is being used except for the dynacord h5000.  This is for live music not dj. 

4 qrx115
2 qrx 118
dx38
2 cp4000s
1 dynacord h5000

My questions are
1. Should I keep the h5000 or is it just too much power?  The sound of the Dynacord amp sounded sweeter than the cp4000s which is causing my dilemma.
2.  If I keep it, how should i set my limiters on the dx38 so that i dont blow my tops? 
3.  If I had the dynacord on tops, i was thinking of bridging the cp4000s and using one per sub. again how should i set my limiters here without blowing them?
4.  I currently run one cp4000s for highs and one for subs, it seems like we we get close to running out of headroom most of the time, which is why im asking the above questions. 

All help would be appreciated
To begin, this post should be in the Lounge.  A single cp4000s is a very good match for your tops (either 2 or 4) in stereo.  The Dynacord H5000 is a very good match for your subs.  What else do you really need to know?
Logged
Scott Wagner
Big Nickel Audio

Alfred Popaj

  • Newbie
  • *
  • Offline Offline
  • Posts: 4
Re: Help with setting up EV QRX/dx38/ dynacord h5000/ and cp4000s
« Reply #2 on: October 02, 2013, 04:17:34 PM »

To begin, this post should be in the Lounge.  A single cp4000s is a very good match for your tops (either 2 or 4) in stereo.  The Dynacord H5000 is a very good match for your subs.  What else do you really need to know?

sorry just copied and pasted to the other board.
Logged

Scott Wagner

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1020
  • Richmond, VA
Re: Help with setting up EV QRX/dx38/ dynacord h5000/ and cp4000s
« Reply #3 on: October 02, 2013, 04:52:28 PM »

sorry just copied and pasted to the other board.
No need for that.  The Moderators would/will move it for you.
Logged
Scott Wagner
Big Nickel Audio

ProSoundWeb Community

Re: Help with setting up EV QRX/dx38/ dynacord h5000/ and cp4000s
« Reply #3 on: October 02, 2013, 04:52:28 PM »


Pages: [1]   Go Up
 



Site Hosted By Ashdown Technologies, Inc.

Page created in 0.035 seconds with 23 queries.