I finally got a chance to get outside today, and do some testing on some of the LAB's favorite speakers, the EV QRX212, and the Yorkville U15. I've broken the review up into a few different sections, just so I can cover everything and not miss any details.
Before we get into any of the technical stuff, lets just have a look at the cabs themselves...
They are very similar in size, and weight. Build quality on both cabs is very good. However, the grill on the QRX212 is much more solid. When I was picking the cabs up with the grills against my chest, the U15's would flex, while the QRX would stay solid. The foam backing on the QRX also makes for a much cleaner look.
The both weigh pretty much the same, and are easy to handle. The U15 is shorter, fatter and deeper then the QRX212.
You guys can check out the specs for either cab if you'd like:
http://www.electrovoice.com/products/193.html http://www.yorkville.com/products.asp?type=29&cat=38& ;id=254
SMAARTThe tests were, for the most part, very unscientific and I relied on my ears, and a few of my buddies for most of the results. The cabs were run passive, as I did not want to get into biamping them. The setup consisted of:
1 macbook computer for playback/smaart
1 Yamaha MG10 mixer for the reference mic/playback
1 Crown XS1200 for power
I later added in a dbx DR260(only DSP I had laying around) for some EQ stuff.
First up, I took some SMAART measurements outside to see what the speakers raw response looked like. I had no HFP's in place and no EQ at all for these measurements.
I started with a ground plane setup, but I was getting a lot of false readings in the low mid sections, thanks to the ground coupling. I wanted to get the cabs more into free space so we could really see what their response looked like, so I settled for an on axis measurement, with the cabs 22" off the ground:
Here's what SMAART said:
White = QRX212
Orange = U15
Listening test:For the listening test, I wanted to make sure everything was matched, so one cab didn't get an unfair advantage. I had the QRX212 on channel 1 of the XS1200, and the U15 on channel 2. The MG10 was plugged straight into the amp.
I played pink noise and brought the U15 up so it was doing 102dBC @ 1m. I panned over to the QRX212, and didn't have to touch a thing. I was surprised to see that it was 102dBC @ 1m without touching anything. On paper, the EV cab has a 3dB advantage over the U15, but with the gains wide open on both amp channels, the cabs were the exact same level right off the bat. So, either the U15 is more efficient then Yorkville says, or the QRX is a little less.
Anyway, on to listening. Our track of choice was: Donald Fagen: Ruby Ruby, along with a few others later on...
With no EQ on either box, there were some pretty drastic differences between the 2. We all agreed that the U15 had much better extended top end with no EQ, but it was missing some of the meat of the mid range. You could say that the U15 had more of a "hi fi" sound. The QRX212 lacked the top end sparkle that the U15 had.
The QRX was more mid range heavy, and that 5k peak SMAART showed was very apparent with music. The QRX also had a lot more low mids, and lows. The U15 seemed to disappear below 80hz, while the QRX212 was solid much lower.
I also noticed that the QRX212 had a much more detailed mid range. The pianos, cellos, snare/toms and guitars sounded a lot better on the QRX cabs. The cymbals, and vocals sounded better on the U15s(thanks to that extended top end). But, the U15 just seemed to have a hole in the mid range, not giving the cab any bite, or cut.
So, I decided to throw the DR260 into the mix. I put a 70hz, 18dB BW HPF on both cabs, and did some EQ on the EV's. I did 2 simple things. A 6dB cut @ 4.5k, and a 12dB/oct hi-shelf @ 10k. What a difference! The top end everyone wanted was now there on the EV's, and the 5k bite was gone. The U15 was the early leader, but with 2 little EQ changes, everyone started to like the QRX212 a lot more. It still didn't have an ultra sparkly high end, but it was there. The QRX212 had a lot "fuller" sound to it that didn't hurt my ears at all, while the U15 was still missing some lower mids, and the HF was actually getting painful as we cranked it.
I wanted to see what these cabs could do, so it was time to let them loose. I had no limiters in place, just the 70hz HPF, and those 2 EQ cuts on the EV. I cranked the music up until the clip light started to tickle on the amp. The QRX212 stayed fairly smooth, and very full sounding. It was very impressive. Those 12's had a fair amount of ass to them. They were able to maintain 117dBC @ 12' when the amp started to run out of gas.
Next up, was the U15. Again we cranked it up, but I had to turn it right down. OUCH! The HF on those cabs got painful quick! That added sparkle that sounded nice at lower levels really started to hurt at higher levels. I had to put 2 filters on the MF/HF to smooth it out. The first was a 4dB cut @ 2.5k, and another wide 3dB cut 6.3k. Ok, so we turn it up again. Much better, but still a little harsh. It seems as if the 1" compression driver is not loving it at all. I made another cut at 8K, and it seemed to help. What surprised me though, is that the U15 was also to maintain 117dBC @ 12' when the amp started to run out of gas. It just wasn't as smooth as the QRX212.
I was out of amp power, and time. So, we called it a day and picked the winner. Myself and one other guy picked the QRX212, while the other guy picked the U15. I wish I would have had time to biamp the cabs and really give them a good beating, but that will have to wait for another day...
So, to sum it up:
EV QRX212:
-More detailed mid range
-Good top end with a little EQ
-Fuller sounding
-More "cut," better for rock and roll
Yorkville U15:
-Better top end
-More sparkle
-Missing the midrange meat
Both cabs sound fine, and it really comes down to personal preference. I will say, that I know from live usage the EV cabs will get louder, and sound better with bands(when you push them). It just really depends on what you're looking for in a speaker.
Evan