Print

Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

[Vladimir Angelovski]

Ok Lan1 and Lan2 led's indicate the ports are active.
Windows connects to the router.  The driver for the digital unit is installed.  Firewall? Disable firewall and try.
Also
Open your web browser(IE,Firefox,Safari,etc) -->find the address bar-->leave it blank-->type  http:// 192.168.1.1-->Press enter.
Take a good look at the router settings and make sure everything is as it should be.

Hello Stu,

The firewall is disabled. Drivers installed. I did go to the router settings page that you mentioned, everything seems like it should be. Is there anything particular that I might oversaw, any ideas?

Thank Stu!

[Vladimir Angelovski]

Hi Eric,

Settings for PROCESSOR:
IP address: 192.168.1.3
MAC address: 00-A0-DE-25-1F-E6

Settings for ROUTER:
IP address: 192.168.1.1
MAC address: 08-10-77-33-32-D1
Subnet: 255.255.255.0

Settings for LAPTOP:
IP address: 192.168.1.2
MAC address: 00-1A-4B-81-04-DA
Subnet: 255.255.255.0
Default gateway: 192.168.1.2

Laptop and processor are connected via CAT5 cable to ports LAN1 and LAN2 on the router.

Eric, how can I ping the processor, what should I type in the command line?

Thanks!

[Bob Leonard]

Vlad,
I do not see a mask assigned in the settings posted above. Please go to the processor and set the IP address as shown below.

address - 192.168.1.3

mask - 255.255.255.0

gateway - 192.168.1.1

Once done open a command prompt on your laptop and type;

ipconfig /all

then - tracert 192.168.1.1

then - tracert 192.168.1.3


Reply with a screen shot of the returned info if the mask does not fix the problem.

[Vladimir Angelovski]

Vlad,
I do not see a mask assigned in the settings posted above. Please go to the processor and set the IP address as shown below.

address - 192.168.1.3

mask - 255.255.255.0

gateway - 192.168.1.1

Once done open a command prompt on your laptop and type;

ipconfig /all

then - tracert 192.168.1.1

then - tracert 192.168.1.3


Reply with a screen shot of the returned info if the mask does not fix the problem.

Hi Bob,

thanks for the reply.

Attached are the only three pages from the manual. The subnet and the gateway are set by default in the processor.

Does this clears it a bit? I will now go and try those command lines you sent me.

Thanks!

[Vladimir Angelovski]

page 2

[Vladimir Angelovski]

page 3

[Bob Leonard]

Have you installed the latest DME network driver on the PC, and does it need to be configured before detection is possible?
 
 

[Vladimir Angelovski]

Have you installed the latest DME network driver on the PC, and does it need to be configured before detection is possible?

Hello Bob,

I have installed the DME network driver from this page:
http://www.yamahaproaudio.com/global/en/downloads/firmware_software/dmen/dme_des400.jsp

Where can I find that dialog box that you posted?

Driver only instals itself and reboots the system, there is no configuration option.

[Bob Leonard]

Vlad,
I found this in the manual, page 13. I'm not a user of the software so I really can't say, just doing some research hoping maybe I could help shed some light on the subject. I would say that if you have not configured the DME network app you're headed in the right direction. Now would be the time to call Yamaha support.

[Vladimir Angelovski]

Vlad,
I do not see a mask assigned in the settings posted above. Please go to the processor and set the IP address as shown below.

address - 192.168.1.3

mask - 255.255.255.0

gateway - 192.168.1.1

Once done open a command prompt on your laptop and type;

ipconfig /all

then - tracert 192.168.1.1

then - tracert 192.168.1.3


Reply with a screen shot of the returned info if the mask does not fix the problem.

I can make in the processor IP address as you suggested, but it automaticly sets its gateway with the same numbers, there is no option for IP address and gateway to be different.

there is a printscreen when I typed first "tracert" command, but on the second one Laptop couldn't find it.

[ProSoundWeb Community]