Print

Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

[Vladimir Angelovski]

Hi guys,

I have:
Yamaha SP 2060 speaker processor,
HP Compaq 6715s laptop,
Netis WF-2409 Wireless Router
Yamaha DME Designer software

Since I am a networking dummie I have problems making SP2060 connect with HP laptop. In DME Designer software, I always get the message "Communication port not set up." no matter what I did.
Can anyone tell me what settings should I use (IP addresses, subnet, gateway, etc...)to make it all work and how to connect it?

Thanks!

Please move this post in "lite" area if needed. Cheers!

[Mike Eiseman]

Did you also install and configure the DME-N Network Driver?

http://www.yamahaproaudio.com/global/en/downloads/firmware_software/networkdrivers/

Hi guys,

I have:
Yamaha SP 2060 speaker processor,
HP Compaq 6715s laptop,
Netis WF-2409 Wireless Router
Yamaha DME Designer software

Since I am a networking dummie I have problems making SP2060 connect with HP laptop. In DME Designer software, I always get the message "Communication port not set up." no matter what I did.
Can anyone tell me what settings should I use (IP addresses, subnet, gateway, etc...)to make it all work and how to connect it?

Thanks!

Please move this post in "lite" area if needed. Cheers!

[Vladimir Angelovski]

Did you also install and configure the DME-N Network Driver?

http://www.yamahaproaudio.com/global/en/downloads/firmware_software/networkdrivers/

Yes I did install it.

[Stu McDoniel]

Hi guys,

I have:
Yamaha SP 2060 speaker processor,
HP Compaq 6715s laptop,
Netis WF-2409 Wireless Router
Yamaha DME Designer software

Since I am a networking dummie I have problems making SP2060 connect with HP laptop. In DME Designer software, I always get the message "Communication port not set up." no matter what I did.
Can anyone tell me what settings should I use (IP addresses, subnet, gateway, etc...)to make it all work and how to connect it?

Thanks!

Please move this post in "lite" area if needed. Cheers!

First make sure Windows has an established connection with the wireless router as that is your port to the Yamaha device.

[Vladimir Angelovski]

First make sure Windows has an established connection with the wireless router as that is your port to the Yamaha device.

Yes, windows sees Netis router perfectly, I tried it through a cable and through wireless connection. So the problem is that laptop and router don't see the processor.

I don't know if it matters, LEDs on the front side of the router that read LAN1 and LAN2 both are lit when I plug ethernet cables, one from laptop and the other from processor.

Any ideas how to make this work?

[Stu McDoniel]

Yes, windows sees Netis router perfectly, I tried it through a cable and through wireless connection. So the problem is that laptop and router don't see the processor.

I don't know if it matters, LEDs on the front side of the router that read LAN1 and LAN2 both are lit when I plug ethernet cables, one from laptop and the other from processor.

Any ideas how to make this work?

Ok Lan1 and Lan2 led's indicate the ports are active.
Windows connects to the router.  The driver for the digital unit is installed.  Firewall? Disable firewall and try.
Also
Open your web browser(IE,Firefox,Safari,etc) -->find the address bar-->leave it blank-->type  http:// 192.168.1.1-->Press enter.
Take a good look at the router settings and make sure everything is as it should be.   

[Erik Jerde]

Make sure you can ping the processor from your computer.  If you can't then nothing else will work either.

What are your network settings anyways?  Both computer and processor IP, net mask, and gateway.

[Rob Spence]

Did you read the instructions from Yamaha?


Sent from my iPad using Tapatalk HD

[Vladimir Angelovski]

Make sure you can ping the processor from your computer.  If you can't then nothing else will work either.

What are your network settings anyways?  Both computer and processor IP, net mask, and gateway.

Hi Eric,

Settings for PROCESSOR:
IP address: 192.168.1.3
MAC address: 00-A0-DE-25-1F-E6

Settings for ROUTER:
IP address: 192.168.1.1
MAC address: 08-10-77-33-32-D1
Subnet: 255.255.255.0

Settings for LAPTOP:
IP address: 192.168.1.2
MAC address: 00-1A-4B-81-04-DA
Subnet: 255.255.255.0
Default gateway: 192.168.1.2

Laptop and processor are connected via CAT5 cable to ports LAN1 and LAN2 on the router.

[Vladimir Angelovski]

Did you read the instructions from Yamaha?


Sent from my iPad using Tapatalk HD

Yes ROB, I did. There is no explanation how to set adresses up, and there is no troubleshooting page. Any idea of how to make the connection worh is highly appreciated. Thanks.

[ProSoundWeb Community]